Mid-Continent Composites

User Name Remember Me? Password

Welcome to the Mid-Continent Composites. If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Welcome!

	Forum	Last Post	Threads	Posts
	Welcome to the Mid-Continent Composites Technical Forums! Welcome to the Mid-Continent Composites Technical Forums!	Glad to be here! by Joe 12-24-2011 06:53 PM	2	2
	Why www.santaclaritaridingclub.com? Why www.santaclaritaridingclub.com?	Why 'Santa Clarita Riding... by Mongo 12-23-2011 09:35 AM	1	1
	Forum Rules Forum Rules	Forum Rules by Mongo 12-23-2011 09:29 AM	1	1
	Introduce Yourself Tell Us About Yourself and Why You are Interested in Composites.	Joe by Emanuel91 01-11-2012 02:29 AM	1	2

Tooling

	Forum	Last Post	Threads	Posts
	Tooling A Composite Part is Only as Good as the Tools Used to Make It!!	Never	0	0
	Soft Tools Hot Wired Foam, Machined Foam, Wood, etc. What are you questions and comments?	Lower Surface Female Layup... by Joe 02-20-2012 01:35 PM	6	6
	Low Rate Initial Production (LRIP) Tooling Composite, Aluminum, ?? What are your experiences in designing and producing LRIP tools? What are your questions?	Never	0	0
	Production Tools Any questions or suggestions? What are your lessons learned on designing and fabricating production tools?	Never	0	0

Composite Systems

	Forum	Last Post	Threads	Posts
	Polyester / Vinylester Resins When should one choose these systems? What lessons have you learned about polyester / vinylester resins? Any questions regarding polyester / vinylester resins?	Never	0	0
	Epoxies When should one choose these systems? What lessons have you learned about epoxy resins? Any questions regarding epoxy resins?	Just What Is SPOOGE??? by Joe 02-09-2012 02:49 PM	2	3
	Bucket and Brush When should you use B&B? What are the advantages and what are the disadvantages? What ‘tricks’ can you share on using B&B techniques? Questions on B&B?	Never	0	0
	Prepregs – Carbon/epoxy or glass/epoxy prepreg experiences? What systems do you use and why? Any questions regarding carbon/epoxy or glass/epoxy prepregs? Everyone has a ‘lesson learned’ about epoxy prepregs. What is yours? Room Temp / oven / autoclave cured? What is your experience?	Never	0	0
	Pregregs – Phenolic/carbon or phenolic/ glass – room temperature / oven / autoclave cured? What has been your biggest challenge in using phenolic prepregs? Any questions?	Never	0	0
	Resin Infusion – RTM / VARTM / ?? Any resin infusion information/experiences you would like to share? Questions? Do you use analysis tools for designing your RTM or VARTM processes?	Never	0	0

Analysis and Test Tools

	Forum	Last Post	Threads	Posts
	Do you use FiberSim? If so, what do you think?	Never	0	0
	What do you use for composites stress analysis?	Practical Composites Stress... by Joe 01-15-2012 09:43 PM	1	2
	How have you validated your analysis tools?	Never	0	0

Fabrication and Assembly

	Forum	Last Post	Threads	Posts
	Trim & Drill Fixtures What do you use for trim and drill fixtures and why? What are you questions on T&D fixtures? Lesson learned?	Never	0	0
	Bonding composites – Co-Bonded, secondary bonded joints – how do you do it? What are your techniques/lessons learned? What are you questions?	Never	0	0

Aircraft

	Forum	Last Post	Threads	Posts
	Homebuilt Composite Aircraft Are you building a homebuilt? What are you building? What are you considering to build? What are you questions?	Never	0	0
	Canard Aircraft Anyone building a canard airplane or considering a canard? What are your thoughts and questions regarding canard aircraft? What are you experiences building / flying canards?	Rutan canard designs by Joe 02-08-2012 01:21 PM	2	3

Other Composite Projects

	Forum	Last Post	Threads	Posts
	Anyone building a composite boat? What can you share about your experience building a boat? What are your questions?	Never	0	0
	Other composite projects??	Never	0	0

What's Going On?

Currently Active Users: 7 (0 members and 7 guests)
	Most users ever online was 99, 02-15-2011 at 10:03 PM.
Mid-Continent Composites Statistics
	Threads: 16, Posts: 20, Members: 6, Active Members: 1 Welcome to our newest member, jim

New posts     No new posts    A locked forum